ServicesEquipment Installation
Pool Equipment Installation in Higley
When a pump, filter or heater has run its course, we replace it with gear sized for your pool. One person handles your job from the first look at the equipment pad to the final walk-through, so you always know who to ask.
New equipment, put in right the first time
Pool equipment works as a team. The pump moves the water, the filter catches the dirt, and the heater or salt cell does its job only if the flow is right. Put a pump that is too big on a small filter and you get high pressure, short filter life and a bigger power bill. We look at the whole pad before we recommend anything.
Most installs we do are pumps, cartridge and sand filters, heaters, heat pumps, salt chlorine generators and automation controls. Some homeowners call us after a motor dies. Others want to swap an old single-speed pump for a variable-speed model that can run longer and quieter at low speed through a long summer.
We are firefighter owned and operated. That shows up in how we treat the parts of this job that can hurt someone: the electrical connections, the bonding wire and the gas line to a heater. Those get checked, not assumed.
What an install includes
Sizing for your pool
We figure your pool's gallons, the pipe size and how far the water travels. That tells us which pump and filter fit. You get a recommendation with the reasons behind it, not the biggest model on the shelf.
Removal of the old unit
We disconnect and haul off the old pump, filter or heater. Your pad is left clear.
Plumbing and unions
We cut in new PVC where needed, glue it properly and add unions so the next repair is easier. Fittings are pressure tested before we walk away.
Electrical hookup and bonding
New equipment gets connected to the existing circuit and tied into the bonding wire. If the job needs new wiring or a permit, we tell you before work starts and handle it.
Startup and settings
We prime the system, check pressure and flow, and set run times and speeds. For variable-speed pumps and automation, we set a schedule that fits your pool and the season.
A walk-through with you
Before we leave, we show you the new controls, where the filter pressure should sit and what a normal sound is. Short and practical.
Signs it is time for new equipment
- A pump that screams or hums
- Grinding or screeching usually means worn motor bearings. A hum with no spin often means a failed capacitor or a seized motor. Sometimes a repair makes sense, and sometimes the motor is old enough that replacing the pump is the better buy.
- Filter pressure you cannot fix
- If pressure stays high right after a cleaning, or the tank or cartridge is cracked, the filter may be done. Our filter cleaning service can tell you which it is.
- A heater that will not light
- Error codes, soot or a heater that trips out after a few minutes can point to parts that are not worth chasing on an older unit.
- A salt cell that keeps scaling
- Hard water leaves calcium on the cell plates. After a few years of that, a cell stops making enough chlorine even when it is clean.
- Power bills that jump in summer
- Old single-speed pumps run at full power the whole time. In a hot climate where pumps run long hours, a variable-speed pump can make a real difference.
How install day goes
- 1
A look at your pad
We come out, check the equipment that is there and measure what we need. You get a free quote by phone or in person with the model, the parts and the labor spelled out.
- 2
One contact, start to finish
The same person who gave you the quote orders the equipment and sets the day. If something changes, you hear it from them, not from a front desk.
- 3
Water off, old unit out
We shut off power at the breaker, close valves, drain what needs draining and pull the old unit. Most single-piece swaps take part of a day.
- 4
Install and test
New equipment goes in, plumbing gets glued and cured, and wiring gets connected and tied into the bonding wire. We run it, watch for leaks and check pressure and flow.
- 5
Cleanup and handoff
We sweep the pad, haul off the old gear and boxes, and walk you through the settings.
What moves the price
There is no single price for an install because no two equipment pads are the same. The model you choose is the biggest piece, and the condition of the pad and plumbing is the next. We list each part and the labor on your quote so you can see where the money goes.
- Type and model
- A variable-speed pump costs more up front than a single-speed one. Heat pumps and gas heaters vary a lot by size and brand.
- Plumbing changes
- A new unit with a different inlet height or pipe size means more cutting and fittings. Old, sun-brittle PVC sometimes has to be replaced along with it.
- Electrical and gas work
- Moving a circuit, adding a breaker or running a gas line adds labor and may need a permit.
- Add-ons
- Automation, a booster pump for a pressure cleaner or a new valve setup all add to the job. We only suggest them when they solve a problem you actually have.
Equipment installation questions
- Should I repair my pump or replace it?
- It depends on the age of the motor and what failed. A bad capacitor or seal is often a cheap fix. A worn-out motor on an older pump usually is not worth rebuilding. We tell you straight which way we would go and why, and our pool repair service covers the fixes.
- Is a variable-speed pump worth it?
- For most pools here, yes. Pumps run many hours a day in summer, and running slow for longer uses much less power than running fast for a short time. It is also a lot quieter.
- Can I buy the equipment myself and have you install it?
- Call us first and tell us the model. We want to make sure it fits your pool and your plumbing before you spend the money. If it does not fit, we will tell you.
- Will my pool be down for long?
- A straight pump or filter swap usually has the pool running again the same visit. Heaters, salt systems and bigger plumbing changes can take longer, and we give you the timeline when we quote the job.
- Do you take care of the pool after the install?
- We can. Many customers add our weekly pool cleaning, which includes chemicals in the monthly price. There is no contract, so you can stop whenever you want. The first month of weekly service is free.
Ready to replace that tired pump or heater?
Tell us what is on your equipment pad and what it is doing. We will come look, give you a clear price and handle the job from there.